Company | Tengen |
Games | 5 in NesCartDB |
Complexity | ASIC |
Boards | 800032 |
Pinout | Tengen RAMBO-1 pinout |
PRG ROM capacity | 256K |
PRG ROM window | 3×8K + 8K fixed |
PRG RAM capacity | None |
CHR capacity | 256K |
CHR window | 1Kx8 or 2Kx2 + 1Kx4 |
Nametable mirroring | H or V, switchable |
Bus conflicts | No |
IRQ | Yes |
Audio | No |
iNES mappers | 064, 158 |
The Tengen RAMBO-1 is an ASIC mapper, canonically designated as mapper 64. This mapper is basically Tengen's version of the MMC3, but with some extra features. The RAMBO-1 came as a 40-pin PDIP. A variant with different mirroring control is mapper 158.
Example games:
The RAMBO-1 has four pairs of registers at $8000-$9FFF, $A000-$BFFF, $C000-$DFFF, and $E000-$FFFF - even addresses ($8000, $8002, etc.) select the low register and odd addresses ($8001, $8003, etc.) select the high register in each pair.
7 bit 0 ---- ---- CPKx RRRR ||| |||| ||| ++++- Specify which bank register to update on next write to Bank Data register ||| 0000: R0: Select 2 (K=0) or 1 (K=1) KiB CHR bank at PPU $0000 (or $1000) ||| 0001: R1: Select 2 (K=0) or 1 (K=1) KiB CHR bank at PPU $0800 (or $1800) ||| 0010: R2: Select 1 KiB CHR bank at PPU $1000-$13FF (or $0000-$03FF) ||| 0011: R3: Select 1 KiB CHR bank at PPU $1400-$17FF (or $0400-$07FF) ||| 0100: R4: Select 1 KiB CHR bank at PPU $1800-$1BFF (or $0800-$0BFF) ||| 0101: R5: Select 1 KiB CHR bank at PPU $1C00-$1FFF (or $0C00-$0FFF) ||| 0110: R6: Select 8 KiB PRG ROM bank at $8000-$9FFF (or $C000-$DFFF) ||| 0111: R7: Select 8 KiB PRG ROM bank at $A000-$BFFF ||| 1000: R8: If K=1, Select 1 KiB CHR bank at PPU $0400 (or $1400) ||| 1001: R9: If K=1, Select 1 KiB CHR bank at PPU $0C00 (or $1C00) ||| 1111: RF: Select 8 KiB PRG ROM bank at $C000-$DFFF (or $8000-$9FFF) ||+------- Full 1 KiB CHR bank mode 0: two 2 KiB banks at $0000-$0FFF (or $1000-$1FFF) || 1: four 1 KiB banks at $0000-$0FFF (or $1000-$1FFF) |+-------- PRG ROM bank mode 0: $8000-$9FFF uses bank selected with R6 | $A000-$BFFF uses bank selected with R7 | $C000-$DFFF uses bank selected with RF | 1: $8000-$9FFF uses bank selected with RF | $A000-$BFFF uses bank selected with R7 | $C000-$DFFF uses bank selected with R6 +--------- CHR A12 inversion 0: two 2 KiB banks (or four 1 KiB banks) at $0000-$0FFF four 1 KiB banks at $1000-$1FFF 1: two 2 KiB banks (or four 1 KiB banks) at $1000-$1FFF four 1 KiB banks at $0000-$0FFF
When $8000 & $80 | is $00 | is $80 |
---|---|---|
PPU Bank | Value of RAMBO-1 register | |
$0000-$03FF | R0 | R2 |
$0400-$07FF | K=0: R0 K=1: R8 |
R3 |
$0800-$0BFF | R1 | R4 |
$0C00-$0FFF | K=0: R1 K=1: R9 |
R5 |
$1000-$13FF | R2 | R0 |
$1400-$17FF | R3 | K=0: R0 K=1: R8 |
$1800-$1BFF | R4 | R1 |
$1C00-$1FFF | R5 | K=0: R1 K=1: R9 |
With 2KiB banks (where K=0), only even-numbered CHR banks can be selected. The lowest bit in the register is ignored and instead passes PPU A10 directly through to CHR A10.
Because the values in R6, R7, RF, and $8000 are unspecified at power on, the reset vector must point into $E000-$FFFF, and code must initialize these before jumping out of $E000-$FFFF.
When $8000 & $40 | is $00 | is $40 |
---|---|---|
CPU Bank | Value of RAMBO-1 register | |
$8000-$9FFF | R6 | RF |
$A000-$BFFF | R7 | R7 |
$C000-$DFFF | RF | R6 |
$E000-$FFFF | (-1) | (-1) |
All eight bits are used for a new value for the bank based on last value written to Bank select register (as mentioned above)
7 bit 0 ---- ---- xxxx xxxM | +- Mirroring (0: vertical; 1: horizontal)
This applies to mapper 64 only (see Variants below).
This register is either not implemented or has undiscovered functionality on RAMBO-1. The MMC3/MMC6 equivalent of this register controls external and internal PRG-RAM access. There is not presently any reason to believe that RAMBO-1 has any support for PRG-RAM.
All eight bits of this register specifies the IRQ counter reload value. When the IRQ counter is zero (or a reload is requested through $C001), this value will be copied into the IRQ counter at the end of the current scanline.
7 bit 0 ---- ---- xxxx xxxM | +- IRQ mode select (0: Scanline Mode, 1: CPU Cycle Mode)
Writing to this register also clears the IRQ counter so that it will be reloaded at next clock, or the next scanline, depending on the selected mode. This also resets the prescaler in cycle mode, so the next clock will occur 4 cycles later.
Writing any value to this register will disable counter interrupts AND acknowledge any pending interrupts.
Writing any value to this register will enable counter interrupts. Note that writing to this register does not acknowledge the IRQ if already set.
There are two IRQ modes: PPU A12 mode (also known as scanline mode) and CPU cycle mode.
In scanline mode, the counter is clocked using a very similar method to that used by the MMC3 and follows the same restrictions. In comparison to the MMC3, the actual interrupt triggers slightly later. Specifically, it is delayed until M2 falls twice after the PPU A12 rise that would have triggered the MMC3 interrupt.
In CPU cycle mode, the counter is clocked every 4 CPU cycles. The actual interrupt triggers one M2 cycle later than one would naively expect.
Whichever IRQ mode is being used, the counter behaves the following way:
When the IRQ is clocked by scanline or CPU cycle modes:
Notes:
Following these rules in scanline counter mode has demonstrated accurate behavior, but this needs to be refined and merged with the description above:
On M2 falling edge: If PA12 = 0: If 4-bit counter < 16: 4-bit counter++. else keep the same value. If PA12 = 1: If 4-bit counter = 16: Clock the 8-bit counter. Always reset 4-bit counter to 0. On 8-bit counter clock: If value = 0: If IRQ is enabled, trigger IRQ (wait 1 more cycle before doing that though, regardless of PA12 next cycle...) Always reload counter with value in $C000. Else value--. On Write to $C001 (reset): Reload 8-bit counter with value in $C000 Set 4-bit counter to 17.
Mapper 158, used for Alien Syndrome, has mirroring like mapper 118 (TLSROM), where CIRAM A10 is connected to CHR A17, and bit 7 of each CHR bank mapped into PPU $0000-$0FFF controls which page of CIRAM is used for the corresponding nametable in $2000-$2FFF.
Categories: MMC3-like mappers, ASIC mappers, In NesCartDB, Mappers with scanline IRQs, Mappers with cycle IRQs